Chipboard-manufacture,factory,supplier from China

   Particle board is also referred to as chipboard or flakeboard, it's a form of wood-primarily based panel made of timber or different lignocellulosic materials and stuck under warmth and strain after applying adhesive.

    Particleboard is a wood-based panel processed from wood or other non-wood plants. The middle layer of the particle board is wood chips, and the two sides are finely-organized wood chips, which are formed by hot pressing with adhesives and other additives. According to the structure, it can be divided into single-layer, double-layer, and gradient structure particle boards. The surface layer of the particleboard is powder layered, and the particleboard with uniform texture is the best.

     Particleboard, also known as chipboard, is a wood-based panel that is made of wood or other lignocellulosic materials and glued under heat and pressure after applying an adhesive.

Particle Board Quality Particle board is also called particle board or particle board. it's miles a form of timber-based panel product of timber or different lignocellulosic substances and stuck under warmness and stress after making use of adhesive. it's also known as chipboard.

Raw material of Particle board.1.Particleboard is made on the basis of scrap materials, but the range of scrap materials is relatively wide. According to different types of scrap materials, particleboard can be divided into wood particleboard, bagasse particleboard, flax chipboard, cotton stalk particleboard, Bamboo particle board, etc., cement particle board, gypsum particle board. It can be seen that most of the scraps contain wood cellulose.

   Particle board, also known as chipboard, is a wood-based board made of wood or other lignocellulosic materials and glued under heat and pressure after applying an adhesive, also known as flake board. It is mainly used in furniture manufacturing and construction industry as well as train and car carriage manufacturing.  Xinhua Wood Company Show  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan.

What is particle board?  Particle board is also called chipboard or flakeboard. It is made of wood or other nitrocellulose materials. It is a wood-based board glued under the action of heat and pressure after applying an adhesive.

The production of chipboard in China has gone through a repeated process from the rise in the 1980s to the decline in the 1990s and then to the rise again in 2000.    After the particle board was abandoned by the market due to poor quality and other reasons, many particle board enterprises learned a lesson, introduced advanced production lines from abroad and improved the technology level.   After that, the quality of particle board in China has improved significantly, and it has been accepted by the market again.

    Particleboard, also known as chipboard, flakeboard, is a wood-based panel that is made of wood or other lignocellulosic materials and glued under heat and pressure after applying an adhesive. It is mainly used in furniture manufacturing and construction industry as well as train and car carriage manufacturing.Method for judging the quality of particleboard wardrobes1. From the appearance point of view, look at the size and shape of the sawdust particles in the center of the cross section. The length is generally 5-10MM.

     Particleboard is also called chipboard or flake board. it's a form of timber-primarily based panel fabricated from wood or different lignocellulosic materials and glued beneath warmth and strain after applying adhesive. it is also called particle board. it is specially used in fixtures production and construction enterprise, in addition to train and car carriage production.Advantage of  Particle Board A. suitable sound absorption, sound insulation and heat insulation performance;B.

   The production of chipboard in China has gone through a repeated process from the rise in the 1980s to the decline in the 1990s and then to the rise again in 2000. After the particle board was abandoned by the market due to poor quality and other reasons, many particle board enterprises learned a lesson, introduced advanced production lines from abroad and improved the technology level.    After that, the quality of particle board in China has improved significantly, and it has been accepted by the market again.

Product performance  The most advanced flat pressing production line in the world. Therefore, the physical performance is higher and better than that of MDF. Its density is usually above 800kg/M3. The high-density fiberboard produced has reached 930kg/M3, which has reached the advanced level of similar products in Europe and America.   The board surface texture is fine and smooth.

  According to their different densities, they are divided into high-density boards, medium density boards and low-density boards. Due to its soft and high impact strength, the density of the density board is uniform after being pressed, and it is also easy to reprocess. It is a good material for making furniture in foreign countries,but its disadvantage is poor water resistance.

          High-density fiberboard (English name: High Density Fiberboard, abbreviated as HDF) is a board made of wood fiber or other plant fiber, applied with urea-formaldehyde resin, or other synthetic resins under heat and pressure.          The most advanced flat pressing complete production line in the world. Therefore, the physical performance is higher and better than that of medium-density fiberboard, and its density is usually above 800kg/M3.

Moistureproof board is to add a certain proportion of moistureproof particles in the production process of the base material, also known as melamine board (base material), which can greatly reduce the degree of expansion of the board when encountering water.  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

Soak the common substrate and moisture-proof substrate in water at the same time, and the expansion rate of the common plate is significantly higher than that of the moisture-proof plate after two hours of expansion change. The moisture-proof board has good moisture-proof performance and is suitable for making kitchen furniture and bathroom furniture.Damp-proof board cannot be directly used on furniture, and decorative paper should be pasted on the surface. The normal practice is to soak the decorative paper in melamine solution, and then press it on after hot pressing.

      Waterproof and moisture-proof board is made by adding special materials that can improve the waterproof, moisture-proof and mildew-proof performance of wood-based panels during the production of medium-density fiberboard.   It is suitable for high-humidity areas and places where accidental humidity may occur, such as kitchens Cabinets, bathroom vanity, laundry cabinet. Marked in green.

     The Waterproof fiberboard originated in Europe. It is based on the production of ordinary fiberboard and added with a certain proportion of granular moisture-proof particles. The fiberboard made in this way can greatly reduce the degree of expansion after encountering water.             Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan. It covers an area of about 76,600 square meters, including a construction area of about 22,000 square meters.

Medium Density Fiberboard (MDF) is a kind of man-made board. MDF is mainly made of plant fibers or wood fibers. It is formed after the fibers are crushed, separated, dried, and urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. Specifications of MDFXinhua Wood StoragesXinhua Wood Quality CertificationsXinhua Wood Introduction    Gaotang County Xinhua Wood Industry Co., Ltd. was established in 2010 . It covers an area of about 76,600 square meters.The company is located in Gaotang County, Liaocheng City,Shandong province, China.

  Density board is made of wood fiber or other plant fiber, prepared by fiber, applied with synthetic resin, and pressed under heat and pressure.Certificates ISO FSC SGS  

    Density board, also known as fiberboard, is a man-made board made of wood fiber or other plant fiber and applied with urea-formaldehyde resin or other suitable adhesives. According to its density, it can be divided into high density board, medium density board and low density board.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. A kind of man-made board.The thickness of MDF is generally between 3mm-30mm, and the density of MDF is very high. Generally, the choice of MDF depends on the density of MDF to determine the quality of MDF. The density of MDF is generally It is in the range of 0.5-0.8g/cm³.

    MDF is actually a kind of density board, which also includes short fiberboard and long fiberboard. MDF is mainly made of plant fibers or wood fibers. After the fibers are crushed, separated, and dried, a urea-formaldehyde resin or other suitable adhesive is added and pressed at high temperature. This kind of man-made board is often used in interior decoration.Xinhua Wood Storage  Quality Certificates  Gaotang County Xinhua Wood Industry Co., Ltd. was established in April 2010 with a registered capital of 11 million yuan.

The following aspects should be paid attention to when choosing medium density fiberboard;1. From the appearance, check whether the thickness and density are uniform, whether the corners are damaged, whether there are delamination, blister, charcolization, etc., and whether there are soft parts.2. When conditions permit, you can saw a small piece of medium density fiberboard and soak it in water with a water temperature of 20°C for 24 hours to observe its thickness change, and at the same time observe whether there are small bulges on the surface of the board.